Category Archives: IPad beanbag

Make an iPad or tablet stand in 15 minutes

Video tutorial: Make an iPad or tablet stand in 15 minutes

All the tablet stands are made in the same way. Make a tube and then fill it up with rice and/or polyfill.

Learn how to make an iPad beanbag or stand

While the video shows how to make an iPad stand:

Make an iPad stand with the leg of a pair of jeans. This is even faster!

Get the sizing and materials for the 4 bean bags  or stands on each link below:

Free tutorials: Make an iPad or tablet  stand in 15 minutes

Tablet stands: 4 free tutorials

I have done 4 iPad stands or bean bags so far:  one using the leg of a pair of jeans, one with patchwork, a simple one using some embellishments and another one with hand painted fabric.

How to make an iPad beanbag out of the leg of a pair of jeans

Make this stand using the leg of a pair of jeans and a pretty button or other embellishment. Watch  this short 4 minute video to learn how to make it.

iPad stands

Patchwork iPad stand

This tablet stand uses 5 inch charm squares. Useful when you have fabric scraps from other projects. Make an iPad stand to match your quilt!

iPad beanbag

This is an even simpler beanbag. It uses just a piece of fabric folded in half and stuffed with batting or polyfill. I added a little flower at the back just for fun.

iPad mini beanbag

iPad mini beanbag

For this stand the fabric has been hand painted with Inktense blocks and a black Sharpie. Derwent Inktense blocks are supposed to be colourfast but I won’t wash the stand just in case.

iPad mini beanbag with hand painted fabric tutorial

Back view

Side view

NOTE: This tutorial is for an iPad mini. If you have an iPad you can use my iPad stand tutorial or my patchwork iPad beanbag tutorial.

Video: How to make an iPad stand or beanbag

Make a tablet stand using the leg of a pair of jeans instead

Materials

  • a 16in x 10in piece of white/cream fabric if you intend to paint it, or any other fabric you’d like to use if not painting it
  • fabric markers or other textile paints such as Inktense
  • buttons
  • polyfill or quilt batting scraps
  • piece of carboard measuring 3 3/4 in for the top, 3 1/4 in for the sides, and 5 3/4 in for the base
  • a stone or other weight or even some rice

Instructions

This project is kind of special because I used hand painted fabric. I did not paint the fabric myself, my daughter did and she used Inktense blocks and a black permanent marker.

Apparently Inktense paints are colour fast once dried though my fingers were slightly stained by handling the beanbag while I was filling it. It could be the marker which was just a normal permanent marker but there was a bit of yellow in it too. In any case I’m not planning to wash the beanbag.

To paint your fabric you can place the fabric directly on to a piece of carboard. I used a stretcher frame I use for silk painting.

I marked the area to be painted and my daughter made the painting.

After it dried, I trimmed the piece to 16in x 10in.

I like the large flowers and the colours my daughter used.

Now fold the rectangular piece in half on the LONG side. I’m using caps because I know this part has been confusing to some people in my previous iPad beanbag tutorial.

Stitch along the long side and one short side as per picture.

Trim the corners to reduce bulk when turning inside out.

Turn inside out and place the bag as per picture, with seam on the bottom.

Fold as per picture below.

Now fold the bottom up to align with the middle point as per picture.

This is where you stitch the buttons.

Make a few stitches in the corner.

Then stitch the buttons on the same point.

Making the cardboard base

To make the cardboard base you can either use the measurements I gave you earlier or you can do what I did which was to do some markings on a piece of cardboard using the still lightly filled bag as a guide.

Then I just cut from dot to.

I had to even it out a bit as the markings were a bit off.

Filling the stand

Time to fill the bag. I used batting scraps for this project. Pull the batting apart first and then start filling the bag little by little.

I also used an old clay figurine as weight. You could use rice instead or a stone. Weight will give the bag some stability.

Once you have filled the bag to your liking, pin along the sewing line. This particular bag is very well stuffed because my daughter wanted to have her iPad mini very upright. This also means that the opening of the bag is a bit uneven as you can see in the photo.

Stitch through the line. This can be hard so you could stitch before you fill the bag completely leaving a small opening on on side and then when well stuffed stitch the little opening.

As you can see there’s quite a bit of fabric left and it looks like it’s wrong. I thought so too but it didn’t turn to be a problem at all. If your bag is not so full the distorsion will be smaller.

Now fold the endings in as per picture.

Stitch almost to the end of the tube leaving an opening.

Fill it in and stitch the opening with a mattress stitch.

Voilà!

iPad / tablet beanbag

This iPad stand can also be made in plain fabric.

Video: How to make an iPad stand


Or you can make it with the leg of a pair of jeans:

Materials

  • 12 charm squares  (5 inch charm squares)
  • 1 self covered button
  • a stone or something heavy for the inside
  • a piece of cardboard
  • polyfill

Print iPad beanbag cardboard base (optional) -it may need adjustments depending on how you like your ipad beanbag to sit.

Assemble the charm squares as in the photo to make a rectangle.

Fold in half, right side facing together, and pin.

Sew around 2 sides to make make a sac.

Place the sac as per photo with both points placed in the middle.

Pick up the bottom point and pin up with the point reaching the middle seam as per photo.

Sew a button in place as per photo below.

Start filling the beanbag using polyfill. Cut a piece of carboard 4 ½ x 4 ½. Place the cardboard inside at the base of the beanbag and the weight on top. Fill around it.

Fill in the beanbag and pin both sides together on the last charm square seam as per photo.

Stitch along the seam leaving a small opening 2 inches wide on one side to top up the filling before closing it completely.

Fold the left over piece into 4 folds.

Pin it.

Stitch both sides of the tube.

Fill the thin tube with polyfill and then sew the tube closed.

Sit the iPad or e-book reader on it.